TURBIN ANGIN SAVONIUS EMPAT SUDU DENGAN VARIASI MODEL PROFIL SEBAGAI MEDIA BELAJAR MAHASISWA

  • Eka Sari Wijianti Universitas Bangka Belitung
  • Saparin Saparin Universitas Bangka Belitung
  • Yudi Setiawan Universitas Bangka Belitung

Abstract

This research is about making a prototype of four blades savonius wind turbine as a learning media for Energy Conversion in the Mechanical Engineering Department, Bangka Belitung University. The making of this learning media is due to the limitations of student practicum facilities to support the continuity of practical and conducive lectures. The prototype was made with small dimensions, namely a frame of 0.75m x 1.5m and a turbine blade diameter of 0.15x0.3m. A fan-assisted the study as a wind energy generator. Wind speed variations carried out at three rates following the wind speed generated by the fan. The rate of wind speed measured using an anemometer and the rotation using a tachometer. The current and voltage are measured using a multitester. Turbine blades are varied with 4 blades with three-blade profile models, namely U, L, and S. Research, shows that wind speed influences turbine performance. The higher the wind speed, the higher the rotor's rotation, and so the resulting power. The best profile is obtained from the L model, which reaches 177.63 rpm with 6.35 watts of power.

Keywords: savonius wind turbine, learning media, wind power generation

Downloads

Download data is not yet available.

References

S. Teknik, M. Energi, F. Teknik, and U. N. Surabaya, “UJI EKSPERIMENTAL TURBIN ANGIN SUMBU VERTIKAL JENIS CROSS FLOW DENGAN VARIASI JUMLAH BLADE Moch Fachruddin Wahyu Permadi Abstrak,” JTM, vol. 06, no. Nomor 1, pp. 25–31, 2005.

E. Pane, “Optimasi perancangan turbin angin vertikal tipe darrieus untuk penerangan di jalan tol,” no. November, pp. 1–2, 2017.

I. S. Mulyana, J. Teknik, M. Fakultas, T. Industri, and U. Gunadarma, “Perancangan Turbin angin vertikal Savonius Sebagai Sumber Energi Untuk penerangan Jalan Tol,” UG J., vol. 11 Nomor 3, p. 27, 2017.

R. Sumiati, D. A. Zamri, S. Pengajar, J. Teknik, M. Politeknik, and N. Padang, “Rancang Bangun Miniatur Turbin Angin Pembangkit Listrik Untuk Media Pembelajaran,” J. Tek. Mesin, vol. 3, no. 2, pp. 1–8, 2013.

C. I. Saputra, C. E. Rustana, and H. Nasbey, “PENGEMBANGAN TURBIN ANGIN SUMBU VERTIKAL TIPE TRIPLE-STAGE SAVONIUS DENGAN POROS GANDA SNF2015-VII-43 SNF2015-VII-44,” vol. IV, pp. 43–46, 2015.

M. H. Haqqqi, G. Nugroho, S. T. Mt, and A. Musyafa, “Rancang Bangun Turbin Angin Vertikal Jenis Savonius dengan Variasi Jumlah Blade Terintegrasi Circular Shield untuk Memperoleh Daya Maksimum,” vol. 7, no. 7, pp. 1–6, 2013.

Hicary, Suwandi, and A. Qurthobi, “Analisis Pengaruh Jumlah Sudu Pada Turbin Angin Savonius Di Dalam Proses Pengisian Akumulator,” vol. 3, no. 3, pp. 4911–4918, 2016.

A. M. Siregar, “RANCANG BANGUN WIND TUNNEL SEDERHANA UNTUK,” vol. 2, no. 2, pp. 92–97, 2016.

Published
2019-10-14
Abstract viewed = 104 times
PDF (Bahasa Indonesia) downloaded = 84 times

Most read articles by the same author(s)