ANALISIS PARAMETER PEMESINAN MESIN CNC LASER DENGAN CONTROLLER ARDUINO UNO PADA BENDA KERJA AKRILIK DENGAN TEBAL 3 MM
DOI:
https://doi.org/10.33019/jm.v11i1.5585Keywords:
CNC laser, MDF board, laser power, engraving speedAbstract
CNC (Computer Numerical Control) machines have revolutionized manufacturing processes and mechanical engineering by replacing manual methods that rely on human labor. A significant innovation in CNC technology is the use of lasers, which are highly beneficial in the engraving industry. CNC Laser machines are used to etch materials like 3 mm thick MDF boards according to predetermined design patterns. The precision level, removal rate, and engraving quality depend on the material properties, laser source characteristics, and laser parameters. The objective of this research is to determine the appropriate machining parameters for 3 mm thick MDF boards and to identify the optimal working time for engraving on this material. The method used in this study is the experimental method. The results of this research show that the feed rate used is 750 mm/min and the laser power is set at 40%, with a processing time of 4 minutes and 42 seconds to complete the engraving of a logo on a 3 mm thick MDF board.
Downloads
References
[2] A. R. Widiyanto, “PROTOTYPE PEMBUATAN CNC DENGAN PEMANFAATAN.”
[3] A. Gumelar, “Rancang Bangun Cnc ( Computer Numerically Controlled ) PCB Layout Berbasis Mikrokontroler P- ISSN : 2302-3295,” vol. 8, no. 3, 2020.
[4] V. Octowinandi, “Pengukuran Hasil Dari Mesin Laser Engraving Pada Material Akrilik Dan Pvc,” J. Appl. Sci. Electr. Eng. Comput. Technol., vol. 3, no. 01, pp. 34–48, 2022, doi: 10.30871/aseect.v3i01.4399.
[5] M. Rosadi, N. F. Inna, and N. R. Wibowo, “Rancang Bangun Mesin CNC 2 Axis Sebagai Mesin Laser Engraving Menggunakan Laser Dioda Pada Media Kayu , akrilik dan tripleks Abstrak,” pp. 13–20.
[6] S. Sragen, “KESIAPAN PELAKSANAAN PEMBELAJARAN PRAKTIK MESIN CNC DI SMK,” pp. 277–286, 2001.
[7] M. D. Purwanto and A. Basuki, “Pemanfaatan teknologi open source untuk meningkatkan mutu produk industri kerajinan,” Pros. Semin. Nas. Ind. Kerajinan dan Batik Membangun Ind. Kerajinan dan Batik yang Tangguh di Masa Pandemi, pp. 1–16, 2020.
[8] D. Sugiyanto, A. S. Uyun, and D. M. Jihad, “Pengaruh Jarak Dan Panas Sinar Laser Terhadap Hasil Engraving Pada Material Kayu Menggunakan Mesin Cnc Laser Diode,” J. Rekayasa Mesin, vol. 14, no. 1, pp. 39–47, 2023, doi: 10.21776/jrm.v14i1.1036.
[9] R. Amany, “Pengaruh Daya Laser CO2 Terhadap Perubahan Warna dan Kekasaran Permukaan Papan Partikel dan MDF,” Fak. Pertan., pp. 1–58, 2022.
Downloads
Published
Issue
Section
License
The paper presented is assumed not to contain proprietary materials that are not protected by patents or patent applications. Responsibility for technical content and for protection from proprietary materials is the responsibility of the author and their organization and not the responsibility of the machine or its editorial staff. The primary author (first / appropriate) is responsible for ensuring that the article has been viewed and approved by all other authors. It is the responsibility of the author to obtain all copyright release permits required for the use of any copyrighted material in the manuscript before submission.
