RANCANG BANGUN PENDINGIN OTOMATIS PADA SAMBUNGAN PLAT BAJA GULUNGAN (HOT ROLL COIL) PASCA PENGELASAN
DOI:
https://doi.org/10.33019/jm.v11i1.6227Keywords:
Sistem pendingin, sensor infrared, Hot Roll CoilAbstract
This research aims to create an automatic cooling device for rolled steel joints (Hot Roll Coil) produced by a nickel processing factory operating in the Morowali Industrial Area. Steel plates in the form of long rolls that are rolled are first welded to connect the steel plates to produce rolls of steel plate that are ready to be marketed. Joining steel using this welding method makes the steel plate hot with a temperature in the range of 100°C-200°C. The temperature of the steel plate after welding must be immediately lowered before rolling, because otherwise the steel joints will come apart and could hamper the production process because the broken plate will have to repeat the welding process from the beginning. The plate temperature required to enter the rolling process is 40°C - 60°C. This research has produced a tool to cool steel joints by automatically spraying the steel joints and succeeded in reducing the plate temperature from 100℃ - 200℃ to a constant temperature of 40℃ - 50℃ according to the required temperature.
Downloads
References
[2] Ghunge.N.C. (2016). Experimental Investigation on the Performance of Soyabean Oil and Blassocut-4000 during Turning of AISI 4130 in terms of Cutting Forces. Laxminarayan Institute of Technology, Nagpur, RTMN University, Nagpur, India, 330-333.
[3] H.F.Muhammad.dkk. (2019). Rancang Bangun Alat Spray Pelumas Sebagai Media Pendingin Pada Proses Milling Dengan Menggunakan Sistem Kontrol Berbasis Arduino Uno. Politeknik Negeri Jakarta, 49-58.
[4] Hadi.W. (2017). Kontrol Kecepatan Motor DC Menggunakan PID Kontroler yang Ditunning Dengan Firefly Algorithm. Program Studi Teknik Elektro Fakultas Teknik Universitas Darul Ulum, 1-9.
[5] Handawi.M.dkk. (2014). Comparison between Nitrogen- Oil- Mist and Air-Oil- Mist Condition. University Teknologi Malaysia, 18-22.
[6] M. Muhammad “Analisis kinerja mesin Spiral Pipe Machine (SPM) produksi pipa baja awwa c 200 dengan menggunakan metode Overall Equipment Effectiveness (OEE) dan Fault Tree Analysis (FTA) di PT. Indal Steel Pipe”., Universitas Muhammadiyah Gresik. 2020
[7] Muh.David.A. (2021). RANCANG BANGUN SISTEM KENDALI SUHU PADA BEARING PROTOTYPE MOTOR INDUKSI. Politeknik Industri Logam Morowali, 1-24.
[8] Oktariawan. (2013). Pembuatan Sistem Otomasi Dispesnser menggunakan Mikrokontrloler Arduino Mega 2560. Mahasiswa Teknik Mesin, Fakultas Teknik Universitas Lampung, 18-24.
[9] Samanglangi.A.M.A. (2021). RANCANG BANGUN SISTEM MONITORING DAN KENDALI PH DAN KONDUKTIVITAS AIR DEMINERALISASI PADA PURWARUPA ECONOMIZER. Politeknik Industri Logam Morowali, 1-40.
[10] Saro.F.S, d. (2018). Rancang Bangun Alat Simulasi Latihan Menembak Berbasis Arduino Uno. Teknik Elektro Fakultas Sam Ratulangi Manado, 251-258.
[11] Shaputra.R, G. (2019). Kran Air Otomatis Pada Tempat Berwudhu Menggunakan Sensor Ultrasonik Berbasis Arduino Uno. Program Studi Teknik Elektro,Fakultas Teknik,Universitas Riau Kepuluan Batam, 192-201.
[12] Wahid.A. (2018). RANCANG BANGUN ALAT PASANG SURUT AIR LAUT BERBASIS ARDUINO UNO DENGAN MENGGUNAKAN SENSOR ULTRASONIK HC-SR04. Fakultas Sains dan Teknik Universitas Nusa Cendana, 102-105.
[13] Wang, M., (2006). Data Fusion of MEMS IMU/GPS Integrated System for Autonomous Land Vehicle, Proceedings of IEEE International Converence on Information Acquisition, pages 80 – 84
[14] R.J. Vidmar, “On the Use of Atmospheric Plasmas as Electromagnetic Reflectors,” IEEE Trans. Plasma Science, vol. 21, no. 3, pp. 876-880, available at http://www.halcyon.com/pub/journals/21ps03-vidmar, Aug. 1992. (URL for Transaction, journal, or magzine)
[15] J.M.P. Martinez, R.B. Llavori, M.J.A. Cabo, and T.B. Pedersen, "Integrating Data Warehouses with Web Data: A Survey," IEEE Trans. Knowledge and Data Eng., preprint, 21 Dec. 2007, doi:10.1109/TKDE.2007.190746.(PrePrint)
Downloads
Published
Issue
Section
License
The paper presented is assumed not to contain proprietary materials that are not protected by patents or patent applications. Responsibility for technical content and for protection from proprietary materials is the responsibility of the author and their organization and not the responsibility of the machine or its editorial staff. The primary author (first / appropriate) is responsible for ensuring that the article has been viewed and approved by all other authors. It is the responsibility of the author to obtain all copyright release permits required for the use of any copyrighted material in the manuscript before submission.
