Evaluasi kinerja dan efisiensi pompa sentrifugal pada sistem pengolahan minyak mentah : studi kasus PT. X
DOI:
https://doi.org/10.33019/jdwcby43Keywords:
centrifugal pump, evaluation of performance, efficiency, crude oilAbstract
Centrifugal pump P100/5 is used to transfer crude oil from the feed tank to the oil processing system at of Refinery PT.X. Evaluating performance and efficiency is essential to ensure the reliability and effectiveness of the processing operation. This study aims to evaluate the performance efficiency of centrifugal pump P.100/5 under actual operating conditions. The research employs a quantitative approach by calculating key performance parameters, including flow rate, head, and pump power. The results indicate that centrifugal pump P.100/5 (Ebara Corporation, 2007), with a design capacity of 25 m³/h and a motor power of 15 kW, has an efficiency performance of 40.94%. This value is still considered acceptable; however, it is not optimal. The primary factor affecting the low efficiency is the oversizing condition, where the pump capacity exceeds the actual system demand. As a result, flow regulation is carried out using a throttling method, which increases head loss and reduces pump efficiency. Several improvement strategies can be applied, including adjusting pump specifications to operate closer to the Best Efficiency Point (BEP), implementing routine maintenance, preventing cavitation, and optimizing system operation. Among these alternatives, the use of a Variable Frequency Drive (VFD) is identified as the most effective solution, as it allows the pump rotational speed to be adjusted according to actual demand, thereby improving energy efficiency and minimizing system losses.
Downloads
References
[1] H. Rezaei, F. Yazdan Panah, C. J. Lim, and S. Sokhansanj, “Pelletization of Refuse-Derived Fuel with Varying Compositions of Plastic, Paper, Organic and Wood,” Sustainability, vol. 12, no. 11, pp. 1–11, Jun. 2020, doi: 10.3390/su12114645.
[2] M. Chaerul and A. K. Wardhani, “Refuse Derived Fuel (RDF) dari Sampah Perkotaan dengan Proses Biodrying: Review,” Jurnal Presipitasi : Media Komunikasi dan Pengembangan Teknik Lingkungan, vol. 17, no. 1, pp. 62–74, 2020.
[3] L. A. Sembiring et al., “Potensi Material Sampah Combustible pada Zona II TPA Jatibarang Semarang sebagai Bahan Baku RDF (Refuse Derived Fuel),” jtm, vol. 7, no. 1, pp. 19–23, Mar. 2018, doi: 10.22441/jtm.v7i1.2240.
[4] M. F. Rania, I. G. E. Lesmana, and E. Maulana, “Analisis Potensi Refuse Derived Fuel (RDF) Dari Sampah Pada Tempat Pembuangan Akhir (TPA) Di Kabupaten Tegal Sebagai Bahan Bakar Incinerator Pirolisis,” sintek. jurnal. ilm. teknik. mesin, vol. 13, no. 1, pp. 51–59, Jun. 2019, doi: 10.24853/sintek.13.1.51-59.
[5] H. Rezaei, F. Yazdanpanah, C. J. Lim, and S. Sokhansanj, “Pelletization properties of refuse-derived fuel - Effects of particle size and moisture content,” Fuel Processing Technology, vol. 205, Aug. 2020, doi: 10.1016/j.fuproc.2020.106437.
[6] I. Brás, M. E. Silva, G. Lobo, A. Cordeiro, M. Faria, and L. T. De Lemos, “Refuse Derived Fuel from Municipal Solid Waste rejected fractions- a Case Study,” Energy Procedia, vol. 120, pp. 349–356, Aug. 2017, doi: 10.1016/j.egypro.2017.07.227.
[7] F. A. Rabbani, T. Sukarnoto, and I. J. M. Afiff, “Rancang Bangun Mesin Pelet Serbuk Kayu Kapasitas 50 kg/jam,” in Semrestek 2022, pp. 1–10.
[8] D. Hendra, “Rekayasa Pembuatan Mesin Pelet Kayu dan Pengujian Hasilnya,” j.penelit.has.kehutan, vol. 30, no. 2, pp. 144–154, Jun. 2012, doi: 10.20886/jphh.2012.30.2.144-154.
[9] T. Mushiri, P. Mugodo, and C. Mbohwa, “Design of a sawdust pelleting machine,” in Proceedings of the International Conference on Industrial Engineering and Operations Management, Rabat, Morocco, 2017, pp. 1763–1776.
[10] D. A. Himawanto, “Karakteristik RDF Dari Sampah Kota Terseleksi Yang Dihasilkan Oleh Pyroliser Ulir,” Jurnal Sains dan Teknologi, vol. 10, no. 2, pp. 188–199, 2021.
[11] E. Suhendi, H. Heriyanto, P. Jundika, and N. Rizkiantika, “Characteristics of Refuse-Derived Fuel (RDF) at The Waste Processing Facility (WPF) of The Faculty of Engineering, Untirta,” World Chemical Engineering Journal, vol. 7, no. 1, pp. 6–10, 2023.
[12] I. W. K. Suryawan, I. M. W. Wijaya, N. K. Sari, I. Y. Septiariva, and N. L. Zahra, “Potential of Energy Municipal Solid Waste (MSW) to Become Refuse Derived Fuel (RDF) in Bali Province, Indonesia,” JBAT, vol. 10, no. 1, pp. 09–15, Sep. 2021, doi: 10.15294/jbat.v10i1.29804.
[13] A. Firdhaus and B. Yunianto, “Analisis Karakteristik Pelet Biomassa Berbahan Dasar Kayu Dengan Campuran Zat Perekat Organik,” Jurnal Teknik Mesin, vol. 11, no. 2, pp. 187–190, 2023.
[14] I. N. Sukarta and P. S. Ayuni, “Analisis Proksimat dan Nilai Kalor Pada Pellet Biosolid Yang Dikombinasikan Dengan Biomassa Limbah Bambu,” j. sains. teknologi., vol. 5, no. 1, Aug. 2016, doi: 10.23887/jst-undiksha.v5i1.8278.
[15] R. Hudayarizka, A. Wulandari, I. K. Ariani, and R. Yorika, “Analisis Variasi Ukuran Partikel Biomassa Cangkang Kelapa Sawit dan Tandan Kosong Kelapa Sawit (TKKS) terhadap Karakteristik Refuse Derived-Fuel (RDF),” sjt, vol. 8, no. 3, pp. 210–222, Dec. 2024, doi: 10.35718/specta.v8i3.1212.
[16] S. Nasiri, A. Hajinezhad, M. H. Kianmehr, and S. Tajik, “Enhancing municipal solid waste efficiency through Refuse Derived Fuel pellets: Additive analysis, die retention time, and temperature impact,” Energy Reports, vol. 10, pp. 941–957, Nov. 2023, doi: 10.1016/j.egyr.2023.07.039.
[17] I. Y. Septiariva, I. W. K. Suryawan, and M. M. Sari, “Vegetable Waste Biodrying Treatment for Energy Recovery as Refuse Derived Fuel Potential,” J. Tek. Kim. Ling, vol. 6, no. 2, pp. 138–146, Oct. 2022, doi: 10.33795/jtkl.v6i2.316.
[18] E. M. Maulidayanti, M. Yuliani, M. H. Robbani, W. Wiharja, E. Hambali, and D. Setyaningsih, “Evaluasi Produksi Refuse-Derived Fuel (RDF) dari Sampah Perkotaan (Studi Kasus: RDF Plant di Kabupaten Cilacap),” Jurtekling, vol. 25, no. 2, pp. 179–189, Jul. 2024, doi: 10.55981/jtl.2024.1008.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Machine : Jurnal Teknik Mesin

This work is licensed under a Creative Commons Attribution 4.0 International License.
The paper presented is assumed not to contain proprietary materials that are not protected by patents or patent applications. Responsibility for technical content and for protection from proprietary materials is the responsibility of the author and their organization and not the responsibility of the machine or its editorial staff. The primary author (first / appropriate) is responsible for ensuring that the article has been viewed and approved by all other authors. It is the responsibility of the author to obtain all copyright release permits required for the use of any copyrighted material in the manuscript before submission.




